Aiwa Portable Stereo System CX NMA545 User Manual

3.5

Out of 6 Ratings

Owner's of the Aiwa Portable Stereo System CX NMA545 gave it a score of 3.5 out of 5. Here's how the scores stacked up:

  • Reliability

    3.5 out of 5

  • Durability

    3.5 out of 5

  • Maintenance

    3.8 out of 5

  • Performance

    3.2 out of 5

  • Ease of Use

    3.5 out of 5
of 88
 
II
The unit can be turned on at a specified time every day with the
built-in timer.
Preparation
Make sure the clock is set correctly.
1
2
3
4
Press one of the function buttons to select a
source.
If TUNER BAND is pressed, the band cannot be selected in
this step.
Press TIMER repeatedly until @ appears on
display.
Time and audio source name flash alternately.
o
the
Within 6 seconds, turn MULTI JOG to designate
the timer-on time, then press ENTER or II.
Turning MULTI JOG changes both the hour and the minute.
++ or - is also available instead of MULTI JOG. Holding
these buttons down will vary the time rapidly.
Within 4 seconds, turn MULTI JOG to select the
duration for the timer-activated period.
The duration can be set between 5 and 240 minutes in
5 minute steps.
++ or ~ is also available instead of MULTI JOG.
5
6
7
Adjust the volume.
The source sound will play at the volume level set in this step
when the power is turned on by the timer.
If the volume level is set to 21 or higher, however, it will
automatically be set to 20 when the power is turned on.
Prepare the source.
To listen to a CD, load the disc to be played first on tray 1.
To listen to a tape, insert the tape into deck 1 or 2.
To listen to the radio, tune in to a station.
o
Press POWER to turn off the power.
When the timer-on time is reached; the unit turns on and
begins play with the selected source.
m
You can change the source that was selected in step 1 by
pressing one of the function buttons before pressing ENTER or
II in step 3.
To check the timer setting
Press TIMER.
The selected source, the timer-on time, and the duration for the
timer-activated period will be displayed for 4 seconds.
To change any of the previous setting
Carry out from step 1,
However, if you do not change the timer-on time, in step 3 just
press ENTER twice and continue from step 4.
To cancel the timer standby mode temporarily
Press TIMER repeatedly so that O disappears.
To restore the timer standby mode, press” again to display ~.
Using the unit while the timer is set
You can use the unit normally after setting the timer.
❑
Before turning off the power, -carry out st;p 5 and 6.
m
● Timer playback and timer recording will not begin unless the
power is turned off.
● Connected equipment cannot be turned on and off by the built-
in timer of this unit. Use an external timer,
Timer recording is applicable for TUNER and VIDEO/AUX (with
an external timer) sources only.
Press either TUNER BAND or VIDEO/AUX to select a source,
then press TIMER repeatedly until @ flashes on the display.
Within 6 seconds, carry out the steps of “SETTING THE TIMER”
from step 3 and insert the tape to be recorded on into deck 2
after step 6.
● When the power-economizing mode (page 9) has been turned
on, the timer recording volume level will be O(minimum level).
● You cannot use the timer function to record from a CD or tape.
The duration will be automatically set after 4 seconds. It will
also be set if ENTER or 1I is pressed within 4 seconds after
step 4.
ENGLISH 25

   Find Your Products By Category