Anchor Audio Microphone XTR-6000CU2 User Manual

0

Out of 0 Ratings

Owner's of the Anchor Audio Microphone XTR-6000CU2 gave it a score of 0 out of 5. Here's how the scores stacked up:

  • Reliability

    0 out of 5

  • Durability

    0 out of 5

  • Maintenance

    0 out of 5

  • Performance

    0 out of 5

  • Ease of Use

    0 out of 5
of 4
 
FEEDBACK
Feedback, a howling noise or shrill sound, is self-generated by the sound system. It’s caused by a microphone picking up the sound
coming from the speaker and then re-amplifying it. Once a feedback loop starts it continues until the system is adjusted.
FEEDBACK CAUSES
• Microphone too close, pointing towards
or in front of speaker
• Volume setting is too loud for room
• Sound reflecting off hard surfaces
AVOIDING & ELIMINATING FEEDBACK
• Point microphone in a different direction
• Keep microphone away from the speaker
• Place speaker in FRONT of the microphone
• Reduce the sound system volume levels
SPEAKER STAND SETUP
DIVERSITY WIRELESS BY ANCHOR AUDIO
Anchor Audio UHF wireless is a 16 channel, diversity wireless system that receives signals with two independent antennae.
With diversity wireless the receiver processes the stronger signal, effectively minimizing dropouts and interference from other
transmitting sources. The antennae are mounted internally so there are no obstructions or risk of damage.
CHANNEL SELECTION - BUILT-IN RECEIVER
Select a channel, set the built-in receiver & microphone transmitter to that channel before useing your wireless system.
1. Choose any available wireless channel/frequency from 1 thru 16 (see page 7 for transmitter setup instructions)
2. Turn the Wireless Channel Selector Knob to the channel/frequency you choose in step 1
If you have two wireless receivers repeat above for the second receiver. Remember each receiver/transmitter pair must be set
to different channels for proper operation.
NOTE: Ongoing wireless interference? The frequency you selected may be in use by
other systems in the area! Change channels until you find a clear frequency!
3
OPERATING THE BUILT-IN CD PLAYER
Your built-in CD player features ‘direct-in’ play, power loading, anti-shock/skip CD mechanism, repeat & random play, three beam
laser tracking system and dual one bit D/A converters. By feeding the CD audio signal directly into the mixing bus the Xtreme Sound
System is able to create a crisp, clear composite output of all your system inputs.
CD PLAYER BASIC OPERATION
Insert a disc into the player by gently sliding it, label side up, into the CD slot. The player will automatically load and begin playback
from the beginning of the disc. CD player controls are explained in detail below:
CAUTION: To avoid noise at shut off, turn CD player off before you turn off the Xtreme!
PLAY/PAUSE Press to play a loaded CD. Press during play-
back to pause, press again to resume.
UP Press once to advance CD to next track. Press
and hold to fast forward on the current track.
DOWN Press once to go to previous track. Press and
hold to fast backward on current track.
EJECT Press to unload a disc from the player. If CD
is not removed within 10 seconds it will be
automatically reloaded into the player.
TOP TRACK Press once to start playing the disc from the
first track.
RANDOM Press for continuous, random track play-back.
Press again to resume normal play.
REPEAT Press for continuous playback of the same
track. Press again to resume normal play.
POWER Press to turn the CD player on/off. The sound
system will need to be turned off separately.
CORRECT SYSTEM PLACEMENT WRONG SYSTEM PLACEMENT
CAUTION: Feedback can damage your equipment
& may be hazardous to hearing.
1. Loosen the Lower Collar Knob
2. Separate the stand legs until
the leg support Cross Braces
are parallel to the floor
3. Tighten the Lower Collar Knob
4. Loosen the Upper Collar Knob and
extend the center pole
5. Adjust height and retighten the
Upper Collar Knob
6. Place your Anchor sound system
on the stand
LOWER
COLLAR
KNOB
UPPER
COLLAR
KNOB
CROSS BRACES
6
WIRELESS VOLUME
CONTROL
CD PLAYER LCD DISPLAY CD POWER ON/OFF
CD SLOT
CONNECTING TWO OR MORE XTREME SOUND SYSTEMS
USING A XTREME UNPOWERED COMPANION SPEAKER (XTR-6001)
Connect one end of a speaker cable (SC-50NL) to the COMPANION SPEAKER OUTPUT jack on the back of a powered Xtreme
sound system. Connect the other end to the jack labeled IN on the back of a Xtreme unpowered companion speaker.
NOTE: AC power is not required for an unpowered companion speaker.
USING POWERED XTREME SYSTEMS
The Balanced Line Output feature allows you to connect two or
more powered Xtreme’s and control all volume levels from the
primary system.
1. Connect a speaker cable (EX-50PP) to the BALANCED
LINE OUT jack on the first/primary powered Xtreme
2. Connect other end of cable to the BALANCED INPUT
jack on the second powered Xtreme
3. Set the Level Control for the Balanced Input on the
second Xtreme to maximum
4. Connect additional systems following 1 - 3 above
NOTE: The Balanced Line Output feature can also be used to send the signal to a
sound system in a different room or a separate recording device.
EX-50PP CABLE
FIRST POWERED
XTREME SYSTEM
SECOND POWERED
XTREME SYSTEM
WIRELESS CHANNEL
SELECTION KNOB
RX INDICATOR LIGHTS

   Find Your Products By Category