Alpine Car Stereo System DVA-7996 User Manual

3.1

Out of 2 Ratings

Owner's of the Alpine Car Stereo System DVA-7996 gave it a score of 3.1 out of 5. Here's how the scores stacked up:

  • Reliability

    3.0 out of 5

  • Durability

    3.5 out of 5

  • Maintenance

    2.5 out of 5

  • Performance

    3.5 out of 5

  • Ease of Use

    3.0 out of 5
of 72
 
58-EN
e Power Supply Connector
r System Switch
When connecting a processor or divider using Ai-NET, place
this switch in the EQ/DIV position. When no device is
connected, leave the switch in the NORM position.
NOTE
Be sure to turn the power off to the unit before changing the
switch position.
t Ai-NET Connector
Connect this to the output or input connector of other
product (CD Changer, Equalizer, etc.) equipped with Ai-
NET.
NOTE
You can input TV/video sound by connecting an optional Ai-
NET/RCA Interface cable (KCA-121B) to this component.
y DC/DC Converter
NOTES
• Do not install the converter at a location subjected to water
such as under the floor mat or air conditioner. This may cause
a malfunction.
• Do not bundle the DC/DC converter cable with other audio
cables. Doing so may induce noise into your system.
• Keep the DC/DC converter away from the Antenna cables and
the rear side of the unit, otherwise noise may be generated
when receiving radio broadcast.
u Ai-NET Cable (Included with CD Changer)
i Front Output RCA Connectors
RED is right and WHITE is left.
o Rear Output RCA Connectors
RED is right and WHITE is left.
; Subwoofer RCA Connectors
RED is right and WHITE is left.
a Audio Output Connectors
RED is right and WHITE is left. Output the audio.
s Video Output Connectors (Yellow)
Output the video.
d RCA Extension Cable (Sold Separately)
1 Antenna Receptacle
2 Power Antenna Lead (Blue)
Connect this lead to the +B terminal of your power antenna,
if applicable.
NOTE
This lead should be used only for controlling the vehicle's power
antenna. Do not use this lead to turn on an amplifier or a signal
processor, etc.
3 Remote Turn-On Lead (Blue/White)
Connect this lead to the remote turn-on lead of your
amplifier or signal processor.
4 Audio Interrupt In Lead (Pink/Black)
5 Remote Control Input Lead (White/Brown)
Connect the external Alpine product to the remote control
output lead.
6 Illumination Lead (Orange)
This lead may be connected to the vehicle's instrument
cluster illumination lead. This will allow the backlighting of
the DVA-7996 to dim whenever the vehicle's lights are
turned on.
7 Switched Power Lead (Ignition) (Red)
Connect this lead to an open terminal on the vehicle's fuse
box or another unused power source which provides (+)12V
only when the ignition is turned on or in the accessory
position.
8 Battery Lead (Yellow)
Connect this lead to the positive (+) post of the vehicle's
battery.
9 Fuse Holder
7.5A
p Ground Lead (Black)
Connect this lead to a good chassis ground on the vehicle.
Make sure the connection is made to bare metal and is
securely fastened using the sheet metal screw provided.
q Digital Output Terminal (Optical)
Use when combining fiber digital input compatible products.
w External Remote
Use when applying the separately sold remote control sensor
unit.
To prevent external noise from entering the audio system.
• Locate the unit and route the leads at least 10 cm away from the car harness.
• Keep the battery power leads as far away from other leads as possible.
• Connect the ground lead securely to a bare metal spot (remove any paint, dirt or grease if necessary) of the car chassis.
• If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries various noise
suppressors, contact them for further information.
• Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.
Installation and Connections

   Find Your Products By Category